S-Video

From Wikipedia, the free encyclopedia

S-Video
A standard 4-pin S-Video cable connector, with each signal pin paired with its own ground pin.
Type	Analog video connector
Specifications
Hot pluggable	Yes
External	Yes
Video signal	NTSC, PAL, or SECAM video
Pins	4 or 7
Connector	Mini-DIN connector
Pin out
Looking at the female connector
Pin 1	GND	Ground (Y)
Pin 2	GND	Ground (C)
Pin 3	Y	Intensity (Luminance)
Pin 4	C	Color (Chrominance)

Separate Video^[1], more commonly known as S-Video, also called Y/C, and sometimes incorrectly ^[2] referred to as Super Video^[3], is an analog video signal that carries video data as two separate signals: luma (luminance) and chroma (color). This differs from composite video, which carries picture information as a single lower-quality signal, and component video, which carries picture information as three separate higher-quality signals. S-Video carries standard definition video (typically at 480i or 576i resolution), but does not carry audio on the same cable.

The 4-pin mini-DIN connector (shown at right) is the most common of several S-Video connector types. Other S-Video connector variants include 7-pin locking "dub" connectors used on many professional S-VHS machines, and dual "Y" and "C" BNC connectors, often used for S-Video patch bays. Early Y/C video monitors often used RCA connectors that were switchable between Y/C and composite video input. Though the connectors are different, the Y/C signals for all types are compatible.

[edit] Overview

The luminance (Y; gray-scale) signal and modulated chrominance (C; color) information are carried on separate, synchronised signal and ground pairs.

In composite video, the luminance signal is low-pass filtered to prevent crosstalk between high-frequency luminance information and the color sub-carrier. S-Video maintains the two as separate signals, so that detrimental low-pass filtering is unnecessary. This increases bandwidth for the luminance information, and also subdues the color crosstalk problem. The infamous dot crawl is eliminated. This means that S-Video leaves more information from the original video intact; thus, it offers an improved image reproduction compared to composite video.

Due to the separation of the video into brightness and color components, S-Video is sometimes considered a type of component video signal; however, it is also the poorest, quality-wise, being far surpassed by the more complex component video schemes, such as RGB. What distinguishes S-Video from these better component-video schemes is that S-Video carries the color information as one signal. This means that the color has to be encoded in some way, and as such, NTSC, PAL, and SECAM signals are all decidedly different through S-Video. Thus, for full compatibility, the connected devices not only have to be S-Video compatible, but also compatible in terms of color encoding. In addition, S-Video suffers from reduced color resolution. NTSC S-Video color resolution is typically 120 lines horizontal (approximately 160 pixels edge-to-edge)^{[citation needed]}, versus 250 lines horizontal for the Rec. 601-encoded signal of a DVD, or 30 lines horizontal for standard VCRs.

When used for connecting a video source to a video display that supports both 4:3 and 16:9 display formats, the PAL television standard provides for signaling pulses that will automatically switch the display from one format to the other. The S-video connection transparently supports this operation. The S-Video connection also has general provision for widescreen signaling through a DC offset applied to the chrominance signal; however, this is a more recent development, and is not widely supported.

[edit] History

In 1987, JVC's release of S-VHS introduced the S-Video cable standard. With S-Video cables, the S-VHS video cassette systems play with their full potential, completing the improved definition and resolution into a compatible TV. Due to low market penetration of television sets and video devices equipped with S-Video ports, the format failed to become a mainstream image standard and remained in the niche high-end home theater market.

In the late 1990s, big-screen television sets began shipping with S-Video option in input ports, thus increasing the number of supportable electronic devices such as DVD players, satellite receivers, and video game consoles. The format gained some popularity as a better alternative to composite video inputs. S-Video was also adopted in the graphics card market in the early 2000s as a video-output solution, from computers to TVs.

The introduction of component video, offering a better image and backward compatibility, replaced S-video as the default alternative to the composite video.

Etymologically, the word S-video has several denotations: Super Video (complementing Super VHS), Separated Video, and S-VHS cable.

[edit] Connector

An S-Video signal is generally connected using a cable with 4-pin mini-DIN connectors. Apart from the impedance requirement, these cables are equivalent to regular mini-DIN cables (like Apple's ADB); these cables can be used for S-Video transfer if no other cable is available, but picture quality may not be as good. Due to the wide use of S-Video connections for DVD players, S-Video cables are fairly inexpensive compared to component or digital connector cables.

The mini-DIN pins, being weak, sometimes bend. This can result in the loss of color or other corruption (or loss) in the signal. A bent pin can be forced back into shape, but this carries the risk of the pin breaking off.

Before the mini-DIN plug became standard, S-Video signals were often carried through different types of plugs. For example, the Commodore 64 home computer of the 1980s, one of the first widely available devices to feature S-Video output, used an 8-pin DIN connector on the computer end and a pair of RCA plugs on the monitor end. (Also available via third-party vendors was an 8-pin DIN-to-4-pin mini-DIN to connect the Commodore directly to a television.) The S-Video connector is the most common video-out connector on laptop computers; however, many devices with S-Video outputs also have composite outputs.

The Atari 800 home computer featured S-Video outputs three years before the Commodore 64, in 1979, via a 5-pin DIN plug.

Both S-Video and audio (mono or stereo) signals can be transferred through SCART connections as well. However, it was not part of the original SCART standard, and not every SCART-compatible device supports it for this reason. Also, S-Video and RGB are mutually exclusive through SCART, due to the S-Video implementation's using the pins allocated for RGB. Most SCART-equipped televisions and VCRs (and almost all of the older ones) do not actually support S-Video, resulting in a monochrome picture if such a connection is attempted, as only the luminance signal portion is usable. Generally, a monochrome picture in itself can also be a sign of incompatible color encoding: for example, NTSC material viewed through a PAL-only device.

Another incompatibility due to S-Video's not being part of the original SCART standard is when connecting a SCART output device such as a cable TV box to a TV with a mini-DIN S-Video input. In many cases, if this connection is made, the result will be a predominantly black-and-white picture, with most of the color (chrominance signal) washed out. An example of this is when connecting a SCART output of a FOXTEL Digital Box (Australia) to a mini-DIN S-Video input of a TV. An impedance mismatch between the SCART and mini-DIN interfaces causes the signal levels to be reduced to the TV, resulting in the poor picture. This problem can be overcome by terminating the chrominance line of the SCART plug with a 75-ohm resistor, correcting the mismatch. Many high-end sets do support this connection, however (without the termination), due to their inputs' having a larger dynamic range.

At least some Fujitsu laptops (S-7020, S-7110) use so-called mini S-Video connector ^[4] for TV-Out. This mini S-Video connector is actually a 3.5mm RCA connector. Such a mini S-Video is however rather rare, and it is very difficult to obtain appropriate cable for it.

[edit] Non-4-pin revisions

[edit] 7-pin mini-DIN

A 7-pin mini-DIN socket.

(Plug or male connector shown, as visible when unplugged; female sockets appear left-right reversed.)

• Nonstandard 7-pin mini-DIN connectors (variant is called "7P") are used on laptops and video cards. A 7-pin socket accepts a 4-pin plug, but not vice versa. However, the pins and the rectangular plastic key on some 4-pin cables may bend when inserted on a 7-pin receptacle. The S-Video signals are available on the four matching pins as before. Of the other three pins, one carries a composite video CVBS (Chroma, Video, Blanking and Sync) signal for non-S-Video displays.

The pinout is as follows - as shown here(pins are numbered from left to right in the diagram above; 4, 7 and 3 on the top row, and 2, 6, 5 and 1 on the bottom row. Thus, the pins that match the 4-pin variant are numbered 1–4 as before).

1 - S-Video Luminance Ground

2 - S-Video Chrominance Ground

3 - S-Video Luminance Signal

4 - S-Video Chrominance Signal

5 - Composite Video Ground

6 - (No Connection)

7 - Composite Video Signal

• The 7-pin plug has a longer locating lug, making it difficult (but not impossible) to insert it in a 4-pin socket. Damage to the plug and socket is inevitable if the plug is forced into the socket.
• A 7-pin connector can also transmit YPbPr or RGB component video, though the outputs are usually three RCA jacks for YPbPr, and five BNC connectors or SCART for RGB. Such cables are often provided with video cards. Used in either of these modes, the pinout is as follows:

1 - Ground (all grounds are connected together)

2 - Ground

3 - Pr (YPbPr) or Red (RGB)

4 - Y (YPbPr) or Green (RGB) [there is no provision for a separate Sync signal]

5 - Ground

6 - Ground

7 - Pb (YPbPr) or Blue (RGB)

• Sometimes (for example, in the ATI radeon HD 2400 XT), pin 5 is composite-video signal, and pins 1, 2, 6, and the connector shield are all connected together, working as both composite ground and S-Video ground. Pin 3 remains S-Video (luminance) and pin 4 S-Video (chrominance).

1 - Ground (all grounds are connected together)

2 - Ground

3 - S-Video Luminance Signal

4 - S-Video Chrominance Signal

5 - Composite Video signal

6 - Ground

7 - ------

• Also, there is such a component/composite variant in the NVidia GeForce 8400 GS:

1 - Ground (all grounds are connected together)

2 - Ground

3 - Pr (YPbPr) or Red (RGB)

4 - Y (YPbPr) or Green (RGB)

5 - Pb (YPbPr) or Blue (RGB) or Composite Video Signal (as a default setting)

6 - Ground

7 - Ground

• Also, there is such a component/composite variant in the NVidia GeForce 8500 GT:

1 - Ground (all grounds are connected together)

2 - Ground

3 - Y (YPbPr) or Green (RGB)

4 - Pr (YPbPr) or Red (RGB)

5 - Ground

6 - Pb (YPbPr) or Blue (RGB) or Composite Video Signal (as a default setting)

7 - Ground

• Also, there is such a component/composite variant in the NVidia GeForce 9500 GT:

1 -

2 -

3 -

4 -

5 -

6 -

7 -

• If one is trying to make a homemade cable, the graphic card cannot send S-Video and composite signals at the same time, so one should not connect them together to the television receiver. The graphic card won't send any signals to help one identify which pins are in charge until one has the right connection and the (S-Video or composite video) sockets plugged into the television receiver while the receiver is turned on. One may not be able to make it if the connection is not the appropriate one for each specific graphic card.^[vague]

• Another type of Y/C signal is to be found on the Sony U-Matic series with a 7-pin connector.

[edit] 9-pin Video In/Video Out

• Two variations of the 9-pin DIN connector are used by video cards with Video In/Video Out (VIVO) capability. Pin-out mapping information for the first version can be found here.

• The pin-out is used in ATI cards (see above, first variation):

1 - Ground (all grounds are connected together)

2 - Ground

3 - Pr (YPbPr) or Red (RGB)

4 - Y (YPbPr) or Green (RGB) [There is no provision for a separate Sync signal]

5 - Ground

6 - Ground

7 - Pb (YPbPr) or Blue (RGB)

8 - Ground

9 - Ground

[edit] Usage

S-Video is commonly used throughout the world with relative popularity. It is found on consumer TVs, DVD players, high-end video cassette recorders, digital TV receivers, DVRs, game consoles, and graphics cards. It has been replaced by component video and digital video standards, such as DVI and HDMI.

S-Video cables are used for computer-to-TV output for business or home use. Because it is very simple to convert S-Video to composite signal (just the physical merging of the two through a filter capacitor is required), many electronics retailers offer converter adaptors for signal conversion. Conversion will not improve image quality, but will allow connecting to otherwise incompatible devices. Converting composite signal to S-Video is harder, because once Luminance and Color are merged, it is hard to separate them while minimizing loss. High quality comb filters are commonly used to separate the signals.

Due to a lack of bandwidth, S-Video connections are generally not considered suitable for high-definition video signals. As a result, HD sources are generally connected to a monitor by way of analog component video or wideband digital methods (usually HDMI or DVI). However, when using older monitors with S-Video but without HDMI and DVI, some graphics cards have full display (including bootup display) with HDMI, DVI, and S-Video and partially full display (displaying only after the OS boots up) with component and composite. So in this case, S-Video works well, as it allows the user to see the display in the event that they need to adjust settings in the CMOS.

The situation with VCRs is a bit unusual: the common S-Video connector was designed for Super VHS and Hi8 VCRs as a high-bandwidth video connection and has been used for the same purpose on a great number of other consumer devices, coming into greatest prominence with the rise of the DVD format. Many digital (and all Hi-8 and S-VHS-C camcorders) support S-Video as well. Standard VHS VCRs do not put out a high enough resolution signal to saturate an S-Video connection, and therefore most such units (even those in combination units with DVD players, which commonly use S-Video or component outputs) require the output from the VHS deck to go through a composite video or RF connection.

In many European Union countries, S-Video is less common because of the dominance of SCART, which allows RGB quality and is required to be on every TV. It is not usual to find S-Video outputs on equipment such as DVD players, although the player may output S-Video over SCART, but the actual TV may not be compatible with S-Video signals and so would just show a black and white image^[5]. In this case it is possible to modify the SCART adapter cable to make it work^[6]. Games consoles usually do not output S-Video either due to the dominance of SCART and the better RGB quality, whilst in the US and other non SCART countries there is S-Video but no RGB. The Nintendo 64 however was an exception - NTSC models could output S-Video, but only with modification could they output RGB. PAL Nintendo 64 models could output S-Video but not RGB despite that being the easiest way to connect if done via SCART. There is however a German company that is able to modify PAL N64's to output true RGB ^[7] although this service is rather expensive compared to the way you can make an NTSC model output RGB.

[edit] Gallery

[edit] See also

• Audio and video connector
• S-VHS
• RCA connector
• RF connector
• Composite monitor
• mini-DIN connector
• List of video connectors
• Video In Video Out (VIVO)

[edit] References

This article was originally based on material from the Free On-line Dictionary of Computing, which is licensed under the GFDL.